Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z

Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z

Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z

Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z

Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z

Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z

Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z

Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z

[Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z]. This product is the ideal spray tool for your exterior metal injection molding to make your workpiece look good and durable. It can spray any metal parts. The formed spray surface can prevent corrosion of various chemicals and ultraviolet rays. It is much stronger than liquid spray and more than ten times stronger than ordinary paint. In the production process, no organic solvent needs to be added, no toxic volatiles are produced, and no environmental pollution is caused. No special training is required to use this product. As long as you read the instructions carefully, you will be able to fully master and operate in a short period of time to realize your ideas and obtain the ideal decorative parts for exterior spray. Power requirements: Use a 220V AC power supply with a safety ground. When in use, the machine must be grounded. Air source requirements: The compressed air pressure used must be between 0.5 and 1.2 kg. It is recommended to use 1.0 kg, and the air pressure at this time is the most ideal. Environmental requirements: well ventilated and dry. Parameters: Power volatge: 110VAC 60Hz, 240VAC 50Hz AMPS: 0.03A voltage output: 25KV+/-5KV Require Air supply: 10-15 PSI, Dry air 5CFM WATTS: 3.3W Power Cord: 16AWG. Air Inlet: 1/4 NPT Thread. A, Power Coating System provides a premium coating ideal for many automotive, marine. Home and garden applications. B, The Powder Coating System is a breakthrough refinishing system for the home hobbyist. Providing professional performance at a fraction of the cost of professional equipment. C, It produces a finish that is resistant to most chemicals, fuels, acids, thinners, brake fluid. UV light, and is much more durable than liquid coatings(up to ten times more durable than ordinary paint). D, Powder coating is environmentally friendly! It produces no toxic wastes and uses no solvents. E, With the Powder, blow it off with compressed air and recoat. Cured powder coating can be recoated with powder and baked or touched up with paint. F, You can operate it without special training. Because the machine generates high-voltage static electricity, the user must use the working place and the equipment must be dry. In addition, the machine must be grounded safely. Do not unplug the grounding plug. This is important to protect the machine and prevent electric shock. To avoid danger, discharge the discharge needle to the grounding clamp after each use. When the particles of plastic powder fall into the air, they will hit the fire source and there is a danger of burning and explosion. Therefore, all hidden dangers must be eliminated and isolated from all fire sources. Do not use a vacuum cleaner to remove the plastic powder on the ground. A dust cover protects the person. Preparation before use: 1. Preparation of sprayed parts: The surface of the parts to be sprayed should be rusted, degreased and phosphated. The parts should have a dry, smooth and clean surface. Prepare one oven, and the brakes will be sprayed into the oven for baking. The parts to be sprayed are preferably hung in an oven with a metal spreader. Prepare the same power supply and socket as the sprayer. The power supply must be equipped with a safety ground. Prepare the air supply. The air supply pressure is generally 0.5 kg to 1.2 kg, and 1.0 kg air source pressure is recommended. Fill the bottle with the dried plastic powder. The plastic powder is about 5 cm from the bottom of the bottle. The sprayed surface powder layer is too thick to form a pile, and the reconstituted plastic surface is granulated after baking. The accumulation of plastic powder can be blown off using air. After the polyester powder is baked, it will cause graininess in the plastic surface, so it is necessary to control the thickness of the surface powder layer. The resulting granular plastic surface can be re-sprayed by smoothing with 400 grit sandpaper. The sprayed surface is not smooth or has pores, which is caused by humidity. It is necessary to replace the dry plastic powder or water vapor separator. If the gun does not spray powder, it may be that the air pressure is too low, or the water in the water vapor separator is too much, causing the air intake to be transported, and the water vapor separator needs to be replaced. The direction of dispersion of the plastic powder during spray molding can adjust the distance between the discharge needle end disperser and the gun body. After drying, if the surface of the part is not ideally sprayed and needs to be re-sprayed, the parts can be sanded with 400 grit sandpaper and then uniformly sprayed and then baked in an oven. If it is found that the duster does not generate high-voltage static electricity, please have a professional knowledge electrical engineer to check and repair, do not use automatic hands to avoid accidents. We have items in stock at USA warehouse and China warehouse, please attention each listing item location. United States, United Kingdom about 2-3 weeks. Canada, Australia, Europe about 3-4 weeks. Other country about 3-5 weeks. Please repack the item carefully. We are professional factory to make kinds of motorcycle CNC accessory, such as kinds of modified brake clutch levers, rearsets, foot pegs, steering dampers, kickstand sidestand, handlebar clamp, swingarm spool bolts and so on. We can offer wholesale and retail, customer order is also can do. We can guantee the items quality and give reasonable price to you. The item “Portable 5-speed Electrostatic Powder Coating system paint Gun coat 220V 110V z” is in sale since Friday, November 22, 2019. This item is in the category “Business & Industrial\Building Materials & Supplies\Painting Equipment & Supplies\Sprayers”. The seller is “cncdeals5″ and is located in China. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.
  • Brand: COLOR TREE
  • MPN: MPNAIKE-02134-I
  • Country/Region of Manufacture: China
  • Power volatge: 110VAC 60Hz, 240VAC 50Hz
  • Plugs: US/UK/AU/EU
  • Note: please tell us which Plugs do you need!
  • AMPS: 0.03A
  • voltage output: 25KV+/-5KV
  • Require Air supply: 10-15 PSI, Dry air 5CFM
  • WATTS: 3.3W
  • Power Cord: 16AWG
  • Air Inlet: 1/4 NPT Thread